Height requirements of electrode paste before filling

 Before filling, the electrode paste should be broken into 80~100mm small pieces, so that the electrode paste can pass smoothly between the two ribs. If the particle size is too large, it is easy to cause electrode paste suspension failure; If the particle size is too small, it is easy to cause spray paste. It is better to buy the finished material of electrode paste. If the material supplied by the manufacturer is of qualified particle size, it can be directly filled. The powder of broken electrode paste is reduced, the utilization rate of electrode paste is improved, and the cost of calcium carbide is reduced. Use a forklift to transport the trolley or special tools to the calcium carbide furnace, and use an electric hoist to hoist it into the electrode barrel. Pay attention to hoisting during loading *.

When adding electrode paste, pay attention not to scatter the electrode paste on the equipment outside the electrode barrel, so as to avoid electric fire accidents. Each time the electrode paste is filled, the site should be cleaned, especially the electrode paste scattered on the equipment. When adding electrode paste, people should not touch the two electrodes at the same time to prevent electric shock. It should also be noted that conductive objects should not remove the two-phase electrodes at the same time to prevent power connection.

In addition, domestic electrode pastes are mostly square and three piece connected. It needs to be broken in use. At present, some manufacturers have improved the shape of electrode paste to make an ellipsoid with appropriate particle size. For example, the sealed electrode paste produced by Fuzhen carbon is 72mm*65mm*120mm, with a mass of about 500g. It has the following advantages:

(1) Loading, unloading, storage and transportation are convenient;

(2) The finished products, loading and other processes have been screened and slag removed for many times, without weight loss;

(3) Less dust pollution, *, reliable;

(4) The particle size is moderate, and there will be no electrode paste spray accident.

The height of electrode paste refers to the height from the upper end of electrode clip to the top of electrode paste. If the electrode paste is too high, the coarse and fine particles in the electrode paste are prone to delamination, or the electrode cylinder is swollen due to the pressure of the paste column. If the electrode paste column is too low, it is difficult to obtain a dense electrode because the pressure of the paste column is too small and the filling property is poor. Electrode paste consumption is too fast. The proper height of electrode paste column is conducive to improving the quality of electrode roasting and reducing consumption.

Comments

Post a Comment

Popular posts from this blog

Study on impurities in high purity flake graphite

Image
 　　For the analysis of trace impurities in high-purity flake graphite, the sample is usually pre ashed or wet digested to remove carbon, the ash is dissolved with acid, and then the impurity content in the solution is determined. The ashing method does not need to use ultra pure acid to dissolve the ash, thus avoiding the risk of introducing the elements to be measured, so it is used more. It is also very difficult to detect the ash content of high-purity flake graphite, because the enriched ash needs to be burned at high temperature, and it is difficult to separate the ash from the sample boat at high temperature, which makes it impossible to accurately determine the composition and content of impurities. 　　The existing methods all take advantage of the characteristic that the platinum crucible does not react with acid, use the platinum crucible to burn the high-purity flake graphite to enrich ash, and then directly heat the sample in the crucible with acid to dissolve th
Read more

General technical index requirements for electrode paste

Image
 Electrode occupies an important position in submerged arc furnace. The working conditions of the electrode are bad, the current passing through is high, the temperature difference between the two ends is large, and the production is affected by the impact of mechanical, electrical and charge collapse... Mechanical strength, higher electrical resistivity, better thermal shock resistance, oxidation resistance and smaller thermal expansion coefficient. Generally speaking, the quality of electrode paste is controlled by the following five indicators: 1. Ash: Ash is the residue of electrode paste when it is burnt to constant weight at 850℃-870℃. It belongs to inorganic minerals. It has high ash resistivity, poor strength, high power consumption, and large electrode consumption. In the event of a hard breaking accident, the ash content is a very important indicator, and the lower the better. 2. Volatile matter: Volatile matter refers to the mass loss of electrode paste under the condition o
Read more

Performance characteristics of anthracite electrode paste

 Anthracite is the main raw material of electrode paste. The performance of anthracite is related to the performance of electrode paste. Therefore, it is necessary to understand and discuss the performance of anthracite to ensure the quality of electrode paste. Anthracite coal in China is mainly distributed in Shanxi, Ningxia and Guizhou. Shanxi is the origin of anthracite, which is mainly produced in Yangquan and Jincheng. Anthracite is an indispensable raw material for carbon industry. It is mainly used in semi graphite cathode carbon block, electric furnace carbon block, blast furnace carbon block, carbon electrode and various pastes. Studying and discussing various properties of anthracite is very beneficial to improve the quality of carbon products.
Read more