Determination method of Cold ramming paste height

 Cold rammed paste has its own precise density, so in this, we can see that the knowledge learned is actually very rich. No matter from what aspect, the characteristics of cold rammed paste are distributed in the middle. What is the method to determine the height of cold rammed paste? Xiaobian will explain it to you today.

Determination method of Cold ramming paste height

　　The height of Cold ramming paste refers to the height from the upper end of the electrode clamp to the top of the electrode paste. If the electrode paste is too high, the coarse and fine particles in the cold rammed paste are prone to delamination, or the electrode cylinder is swollen due to the pressure of the paste column. If the electrode paste column is too low, it is difficult to obtain a dense electrode because the pressure of the paste column is too small and the filling property is poor. The consumption of Cold ramming paste is too fast. The proper height of electrode paste column is conducive to improving the quality of electrode roasting and reducing consumption.

　　By controlling the height of electrode paste, sintered electrodes with good quality can be obtained, which can be controlled by manufacturers according to the actual situation. For example, the electrode diameter of a 25500kva calcium carbide furnace is 1250mm, and the height of the electrode paste should be controlled at 3.5-4.0m, which is more appropriate.

Determination method of Cold ramming paste height

　　Measurement method of Cold ramming paste height:

　　When measuring the height of electrode paste, the tool used is a hemp rope. At one end of the rope, a 100mm*50mm150mm ball made of melted electrode paste is tied. The rope is about 10m, and a mark is made every 200mm.

　　Is the distance (measured value) from the top of the electrode cylinder to the base of the pressure release cylinder (the upper edge of the electrode cylinder jacket), mm; B is the height (measured value) of the empty cylinder of the electrode cylinder, mm; C is the height of electrode paste (calculated value), generally C is 3500-4000mm; D is the height of electrode paste liquid, generally D value is 1000-1500mm; L is the working length of the electrode, about 1800-2000mm from the low ring to the electrode end (the L value of the internal combustion furnace is about 1500-1800mm).

　　The calculation formula of Cold ramming paste height (mm) is as follows:

　　c=6000+600+a-b

Comments

Post a Comment

Popular posts from this blog

Study on impurities in high purity flake graphite

Image
 　　For the analysis of trace impurities in high-purity flake graphite, the sample is usually pre ashed or wet digested to remove carbon, the ash is dissolved with acid, and then the impurity content in the solution is determined. The ashing method does not need to use ultra pure acid to dissolve the ash, thus avoiding the risk of introducing the elements to be measured, so it is used more. It is also very difficult to detect the ash content of high-purity flake graphite, because the enriched ash needs to be burned at high temperature, and it is difficult to separate the ash from the sample boat at high temperature, which makes it impossible to accurately determine the composition and content of impurities. 　　The existing methods all take advantage of the characteristic that the platinum crucible does not react with acid, use the platinum crucible to burn the high-purity flake graphite to enrich ash, and then directly heat the sample in the crucible with acid to dissolve th
Read more

General technical index requirements for electrode paste

Image
 Electrode occupies an important position in submerged arc furnace. The working conditions of the electrode are bad, the current passing through is high, the temperature difference between the two ends is large, and the production is affected by the impact of mechanical, electrical and charge collapse... Mechanical strength, higher electrical resistivity, better thermal shock resistance, oxidation resistance and smaller thermal expansion coefficient. Generally speaking, the quality of electrode paste is controlled by the following five indicators: 1. Ash: Ash is the residue of electrode paste when it is burnt to constant weight at 850℃-870℃. It belongs to inorganic minerals. It has high ash resistivity, poor strength, high power consumption, and large electrode consumption. In the event of a hard breaking accident, the ash content is a very important indicator, and the lower the better. 2. Volatile matter: Volatile matter refers to the mass loss of electrode paste under the condition o
Read more

Performance characteristics of anthracite electrode paste

 Anthracite is the main raw material of electrode paste. The performance of anthracite is related to the performance of electrode paste. Therefore, it is necessary to understand and discuss the performance of anthracite to ensure the quality of electrode paste. Anthracite coal in China is mainly distributed in Shanxi, Ningxia and Guizhou. Shanxi is the origin of anthracite, which is mainly produced in Yangquan and Jincheng. Anthracite is an indispensable raw material for carbon industry. It is mainly used in semi graphite cathode carbon block, electric furnace carbon block, blast furnace carbon block, carbon electrode and various pastes. Studying and discussing various properties of anthracite is very beneficial to improve the quality of carbon products.
Read more