Is electrode paste harmful to human body

 　　The length of the working end of the electrode and the depth of entering the furnace shall be strictly controlled in accordance with the process operation requirements. After each shift, the measurement shall be carried out accurately. The measurement times of each phase of the electrode shall not be less than three times. If the deviation is large, the measurement shall be carried out several times. The average value of the three times with small deviation shall be taken as the length of the working end of the electrode. Only when the length of the working end of the electrode and the depth of entering the furnace are accurately mastered can the operation scheme of the shift be determined, and the pressing length Times

　　As the molten pool of submerged arc furnace not only bears strong high-temperature effect, but also is eroded and mechanically scoured by furnace charge, high-temperature furnace gas, molten iron and high-temperature slag, it is necessary to select specific refractory materials. Requirements for refractory materials: high refractoriness, large changes in shape and volume at high temperature, high temperature strength, good slag resistance, and good chemical stability at high temperature. Various refractory materials shall be kept clean in appearance, complete in structure, free of defects in corners and cracks on the surface.

Copper aluminum composite block is used for crimping. The construction features are simple construction, convenient process supervision, free from the influence of magnetic field, and controllable pressure drop. In 2008, an aluminum plant in Henan adopted this method of connection. Because the technical problems were not solved at that time, the test failed and a short junction explosion accident occurred. However, with the increasing design of electrolytic cell type current, the construction of welding became more and more difficult. It should be seen that the advantages of the crimping method are more and more obvious, and it is believed that the improved crimping method will appear and be gradually adopted,

　　The electrode paste (1) is a common power graphite electrode. Graphite electrodes with current density lower than 17a / m2 are allowed to be used, which are mainly used in ordinary power electric furnaces for steel making, silicon smelting, yellow phosphorus smelting, etc.

　　(2) Oxidation resistant coated graphite electrode. The graphite electrode coated with an anti-oxidation protective layer on the surface forms a protective layer that is both conductive and resistant to high-temperature oxidation, reducing electrode consumption during steel making.

　　(3) High power graphite electrode. Graphite electrode with current density of 18-25 A / m2 is allowed to be used, which is mainly used in high-power electric arc furnace for steel making.

Comments

Post a Comment

Popular posts from this blog

Study on impurities in high purity flake graphite

Image
 　　For the analysis of trace impurities in high-purity flake graphite, the sample is usually pre ashed or wet digested to remove carbon, the ash is dissolved with acid, and then the impurity content in the solution is determined. The ashing method does not need to use ultra pure acid to dissolve the ash, thus avoiding the risk of introducing the elements to be measured, so it is used more. It is also very difficult to detect the ash content of high-purity flake graphite, because the enriched ash needs to be burned at high temperature, and it is difficult to separate the ash from the sample boat at high temperature, which makes it impossible to accurately determine the composition and content of impurities. 　　The existing methods all take advantage of the characteristic that the platinum crucible does not react with acid, use the platinum crucible to burn the high-purity flake graphite to enrich ash, and then directly heat the sample in the crucible with acid to dissolve th
Read more

General technical index requirements for electrode paste

Image
 Electrode occupies an important position in submerged arc furnace. The working conditions of the electrode are bad, the current passing through is high, the temperature difference between the two ends is large, and the production is affected by the impact of mechanical, electrical and charge collapse... Mechanical strength, higher electrical resistivity, better thermal shock resistance, oxidation resistance and smaller thermal expansion coefficient. Generally speaking, the quality of electrode paste is controlled by the following five indicators: 1. Ash: Ash is the residue of electrode paste when it is burnt to constant weight at 850℃-870℃. It belongs to inorganic minerals. It has high ash resistivity, poor strength, high power consumption, and large electrode consumption. In the event of a hard breaking accident, the ash content is a very important indicator, and the lower the better. 2. Volatile matter: Volatile matter refers to the mass loss of electrode paste under the condition o
Read more

Performance characteristics of anthracite electrode paste

 Anthracite is the main raw material of electrode paste. The performance of anthracite is related to the performance of electrode paste. Therefore, it is necessary to understand and discuss the performance of anthracite to ensure the quality of electrode paste. Anthracite coal in China is mainly distributed in Shanxi, Ningxia and Guizhou. Shanxi is the origin of anthracite, which is mainly produced in Yangquan and Jincheng. Anthracite is an indispensable raw material for carbon industry. It is mainly used in semi graphite cathode carbon block, electric furnace carbon block, blast furnace carbon block, carbon electrode and various pastes. Studying and discussing various properties of anthracite is very beneficial to improve the quality of carbon products.
Read more